System STANDARD ROK

System STANDARD ROK

System STANDARD ROK is a new and unique approach to traditional pipe-in-screed underfloor heating, incorporating mineral wool insulation for exceptional acoustic and thermal insulation in addition to excellent fire resistance.

With the ever-increasing concern surrounding the flammability of construction materials Jupiter have launched an underfloor heating system based on fire-resistant mineral wool insulation. The 30 mm mineral wool panels are covered with a stitched on, woven polyethylene sheet. This protects the insulation and its printed grid makes it simple for the installer to position pipes accurately.

The perimeter insulation is also made from mineral wool and comes with an integrated tanking strip to prevent screed from creeping under the panels.

Datasheet
Installation Guide
Case Study

System STANDARD ROK:

Datasheet

Download PDF

Product Specification:

Density:

1950 ± 100

kg / m³

Thickness

30

mm

Insulation Dimensions:

1000 x 1000

mm

Area per Pallet:

40

m²

Mass:

3.15

kg / m²

Fire Classification:

A1

*

Thermal Resistance (R-value):

0.86

m² K / W

Thermal Conductivity (λ-value):

0.035

W / m K

Melting Point:

≥ 1000

° C

Dynamic Stiffness:

≤ 19 SDI

MN / m³

Sound Reduction:

28

dB

Uniform Distributed Load:

5

kN / m²

Compressibility:

≤ 3

mm

* to EN 13501: 2007

Product Benefits:

  • Exceptional fire-resistance.
  • The system meets the minimum insulation requirement for upper floors R-value 0.75 m² K/ W.
  • Increased sound insulation.
  • Totally bio-degradable.
  • Loadable to 20 kN / m².
  • Contains 50% less primary energy than a normal PIR insulation.
  • Complies with insulated floor screeds in building construction requirement, DIN 18560-2.
  • R-Value complies with EN1264.
  • Composed of Rockwool MW 035 DES sm.
  • As well as the obvious fire resistance benefit, System STANDARD ROK has delivers excellent acoustic properties. These combined properties make the system very suitable for apartment projects where both Part E compliance and fire resistance are of paramount importance.
  • Suitable for min. 65 mm sand / cement screeds and 55 mm anhydrite screed.
  • The JUPITER System STANDARD ROK is a new non-flammable system based on Rockwool mineral insulation. Available in varying thicknesses (standard 30 mm) System STANDARD ROK insulation is manufactured with a stitched on, gridded PE foil that allows pipe clip rails to be easily aligned and fixed.

Product Specification:

Density:

1950 ± 100 kg / m³

Thickness:

30 mm

Insulation Dimensions:

1000 x 1000 mm

Area per Pallet:

40 m²

Mass:

3.15 kg / m²

Fire Classification:

A1 *

Thermal Resistance (R-value):

0.86 m² K / W

Thermal Conductivity (λ-value):

0.035 W / mK

Melting Point:

≥ 1000 ° C

Dynamic Stiffness:

≤ 19 SDI MN / m³

Sound Reduction:

28 dB

Uniform Distributed Load:

5 kN / m²

Compressibility:

≤ 3 mm

* to EN 13501: 2007

Product Benefits:

  • Exceptional fire-resistance.
  • The system meets the minimum insulation requirement for upper floors R-value 0.75 m² K/ W.
  • Increased sound insulation.
  • Totally bio-degradable.
  • Loadable to 20 kN / m².
  • Contains 50% less primary energy than a normal PIR insulation.
  • Complies with insulated floor screeds in building construction requirement, DIN 18560-2.
  • R-Value complies with EN1264.
  • Composed of Rockwool MW 035 DES sm.
  • As well as the obvious fire resistance benefit, System STANDARD ROK has delivers excellent acoustic properties. These combined properties make the system very suitable for apartment projects where both Part E compliance and fire resistance are of paramount importance.
  • Suitable for min. 65 mm sand / cement screeds and 55 mm anhydrite screed.
  • The JUPITER System STANDARD ROK is a new non-flammable system based on Rockwool mineral insulation. Available in varying thicknesses (standard 30 mm) System STANDARD ROK insulation is manufactured with a stitched on, gridded PE foil that allows pipe clip rails to be easily aligned and fixed.

System STANDARD ROK:

Installation Guide

Download PDF
01 Begin by placing the perimeter insulation against the wall. When using floor insulation ≥ 5 cm fix the perimeter insulation to the wall above the insulation.
01
Begin by placing the perimeter insulation against the wall. When using floor insulation ≥ 5 cm fix the perimeter insulation to the wall above the insulation.

01

02 Position the first STANDARD ROK insulation panel against the perimeter insulation with the overlapping foil edges facing outwards.
02
Position the first STANDARD ROK insulation panel against the perimeter insulation with the overlapping foil edges facing outwards.

02

03 Ensure that the clear flap (tanking strip) of the perimeter insulation is positioned above the STANDARD ROK. This is to prevent future screed from getting within the perimeter insulation and the panels.
03
Ensure that the clear flap (tanking strip) of the perimeter insulation is positioned above the STANDARD ROK. This is to prevent future screed from getting within the perimeter insulation and the panels.

03

04 When installing further panels ensure that the 50mm foil overlap on each panel covers its neighbouring panels. Panels can be cut using a sharp knife.
04
When installing further panels ensure that the 50mm foil overlap on each panel covers its neighbouring panels. Panels can be cut using a sharp knife.

04

05 Ensure it is dust-free to promote adhesion, and then tape the tanking strip down using a wide and sticky tape.
05
Ensure it is dust-free to promote adhesion, and then tape the tanking strip down using a wide and sticky tape.

05

06 Tape the panels together by running a strip of tape across the 50 mm foil overlap.
06
Tape the panels together by running a strip of tape across the 50 mm foil overlap.

06

07 Remove self-adhesive backing and position pipe clip rails to suit the pipework layout diagram. Cut to length using pipe cutter or blade.
07
Remove self-adhesive backing and position pipe clip rails to suit the pipework layout diagram. Cut to length using pipe cutter or blade.

07

08 Press clip rails firmly into position.
08
Press clip rails firmly into position.

08

09 Clip pipe into clip rails at centres show in pipe layout. Fix flow and return pipes every two metres to prevent them lifting. See additional pipe distance guide in Download PDF for detailed information.
09
Clip pipe into clip rails at centres show in pipe layout. Fix flow and return pipes every two metres to prevent them lifting. See additional pipe distance guide in Download PDF for detailed information.

09

10 When connecting pipe using JUPITER press fittings, only join in straight runs and never on pipe bends. Place pipe in movement gap profiles where designated, protect with black protective sleeve and finally insert expansion gap insulation. See System Standard for further info.
10
When connecting pipe using JUPITER press fittings, only join in straight runs and never on pipe bends. Place pipe in movement gap profiles where designated, protect with black protective sleeve and finally insert expansion gap insulation. See System Standard for further info.

10

System STANDARD ROK:

Case Study

Download PDF
System_Standard_ROK_Case_Studies001

01

System_Standard_ROK_Case_Studies002

02

System_Standard_ROK_Case_Studies003

03

System_Standard_ROK_Case_Studies004

04

System_Standard_ROK_Case_Studies005

05

System_Standard_ROK_Case_Studies006

06